How to lubricate a scanner

palombian

Printer Master
Joined
Feb 4, 2014
Messages
1,869
Reaction score
2,244
Points
297
Location
Belgium
Printer Model
PRO10,PRO9500II,MB5150,MG8250
I have a Mustek Scanexpress A3, a very basic machine but all others cost 10 times more.
The scan wagon blocks regularly.
It glides on one side on a round bar as the printhead in a printer, the other side is just a plastic slider.
It is also pressed by a spring against the underside of the glass with nylon sliders.

What could I use to lubricate ?
 

PeterBJ

Printer VIP
Platinum Printer Member
Joined
Nov 27, 2010
Messages
5,055
Reaction score
4,896
Points
373
Location
Copenhagen Denmark
Printer Model
Canon MP990
My guess is that a lubricant suitable for printers will also be suitable for the scanner. For Canon printers a lubricant Floil KG107A is recommended, but this is hard or impossible to find. A good substitute is Molykote EM-30L. It is safe for plastics and contains no silicone which could cause problems in electronics.

I couldn't find a European distributor that offered a small quantity, so I bought a 2 or 4 oz can at Ebay US. It is still available and I did not have to pay customs and VAT or a special fee for the paper work. I don't know what the rules are for import from US to EU today. I think I bought the grease in 2013. Maybe it will be too expensive? Maybe a European distributor could be found?

Edit: It looks like the grease is also available from Germany and UK.
 
Last edited:

palombian

Printer Master
Joined
Feb 4, 2014
Messages
1,869
Reaction score
2,244
Points
297
Location
Belgium
Printer Model
PRO10,PRO9500II,MB5150,MG8250
FYI, I tried different greases and fine oil but no avail.
Finally I wiped the bar with kitchen paper with silicon spray ( I know you must take care it doesn't migrate in contacts).
I was able to do about 20 scans without any errors.
Fingers crossed, this scanner is really good for the price and as far as I know not on sale anymore.
 

palombian

Printer Master
Joined
Feb 4, 2014
Messages
1,869
Reaction score
2,244
Points
297
Location
Belgium
Printer Model
PRO10,PRO9500II,MB5150,MG8250

SkedAddled

Printer Guru
Joined
Jun 7, 2018
Messages
147
Reaction score
145
Points
137
Location
West Michigan
Printer Model
PRO-100, MG5320, Xerox 6027
Instead of silicone, look for something which carries Teflon in it.

Here in the US, I can get something called Tri-Flow.
It has Teflon in it, carried by light petroleum distillates.
Wiping away a freshly wet application leaves well-lubricated
and clean part(s).

For an application such as your scanner, my approach would be
to clean affected parts with isopropyl, then apply Tri-Flow
using a slightly moistened swab or cloth.

This was our procedure when I was employed by an HP-certified provider
of on-site servicing for HP plotters. Plotters are essentially three- to four-foot-wide
versions of consumer-type ink printers and scanners; they are all similar
in mechanical operation. The steps are easily applied to common
printers and scanners:

1 - Clean the print-carriage path and registration strip with isopropyl.
- Be sure to remove traces of gummed lubricants and contamination.
2 - Wipe dry with a lint-free cloth.
3 - Slightly moisten lint-free cloth with Tri-Flow and apply to carriage path
and registration strip.
4 - Gently wipe again with new lint-free cloth.
This restored like-new mechanical function, every. single. time.

However, BEWARE OF PLOTTERS:
Their long, super-thin registration strips can easily make serious cuts
in your fingers, especially the steel types. HANDLE WITH CARE!
 

Latest posts

Top