Fun 3D Printing Tools - Self Tapping Drill Bits

Nifty

Printer VIP
Administrator
Joined
Nov 3, 2004
Messages
3,046
Reaction score
1,405
Points
337
Location
Bay Area CA
Printer Model
CR-10, i560 ,MFC-7440N
I often print holes into my 3D things in order to either attach them to something, to each other, or attaching things to them.

So, I purchased a kit of metric "screws" / nuts and bolts:
www.amzn.to/35oGOlP

1574228592772.png

They work great, but sometimes I don't want to use a nut with the bolt. So, I've sometimes just printed a whole *slightly* smaller than the screw and tried to use the screw to self-tap into the plastic. Sometimes heating the bolt with a torch and screwing it into the plastic would also help "tap" the hole.

Well, I stumbled on these little gems and they arrived today. I tested them and they work GREAT

Self-drilling self-tapping drill-bits:
www.amzn.to/2XwqJro

1574229045532.png


I'm LOVING these things! Sure, the hold isn't going to be as strong as having a nut/washer on the other side, (or even cooler, an embedded washer), but this is a quick and easy way to get a "good enough" hold for most of the projects I'm working on!
 

Ink stained Fingers

Printer VIP
Platinum Printer Member
Joined
Dec 27, 2014
Messages
5,838
Reaction score
6,965
Points
363
Location
Germany
Printer Model
L805, WF2010, ET8550
Thanks for the tip, I have a set on order, I just needed replacement drills for M3 - M6 anyway.
 

Nifty

Printer VIP
Administrator
Joined
Nov 3, 2004
Messages
3,046
Reaction score
1,405
Points
337
Location
Bay Area CA
Printer Model
CR-10, i560 ,MFC-7440N
Well, I decided to go all-in and also ordered some of these brass inserts:
www.amzn.to/2QBLPDf
 
Last edited:

stratman

Printer VIP
Platinum Printer Member
Joined
Apr 19, 2007
Messages
8,712
Reaction score
7,163
Points
393
Location
USA
Printer Model
Canon MB5120, Pencil
Added to my wish list. Thanks, Rob.
 

Nifty

Printer VIP
Administrator
Joined
Nov 3, 2004
Messages
3,046
Reaction score
1,405
Points
337
Location
Bay Area CA
Printer Model
CR-10, i560 ,MFC-7440N
Am I correct you're planning to use as inserts in a model? How do you get them embedded in a print?
Yup! I plan to use either a soldering iron, or maybe just heat it with a small torch while holding it with pliers.

... and as always, Stephan to the rescue:

 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
Well, I decided to go all-in and also ordered some of these brass inserts:
I would normally use a bolt with a nut and countersink the nut in a slightly larger hole on the back, but I can see the merits of using these Embedded brass nuts instead, so I ordered a pack from AliExpress… :)... Thanks @Nifty...
 

Redbrickman

Printer Master
Joined
Dec 27, 2010
Messages
1,102
Reaction score
1,184
Points
293
Location
UK
Printer Model
MB5150
A good tip when using them is to put the insert in with the soldering iron just a little above the surface then quickly press it against a flat surface to make a neat flush and square finish.

Some inserts are better designed than others too and this video compares them

https://www.youtube.com/watch?v=G-UF4tv3Hvc
 
Top