Maxify is the Pitts..

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
This printer is starting to get up my nose, its doing things that no normal printer has done on me before..

When I first was using I.S. inks, the black channel was always clogging, then I switched to using 3rd party Chinese inks, then the Magenta channel started to clog, I’m now using OEM ink and its causing the yellow channel to clog.

I was using the printer yesterday quite bit more than I normally would, so there’s no excuse for it to clog again, but this morning its back to its old tricks with the yellow channel missing again.

The only good thing I can say is that it prints normally again after a quick clean, it’s as near to a perfect printer as I can get but it still bugs me..
Maxify nozzle.jpg A quick clean and all's normal again..
Click to enlarge..
 

Artur5

Printer Master
Joined
Jan 24, 2011
Messages
1,294
Reaction score
1,618
Points
278
Location
Kmt. 0.
Printer Model
MB5150,Pro10s,i3Mk3s+,Voron2.4
It might be the cartridge and not the ink. Maxify carts, even OEM, are pretty "temperamental".
In my case, no clogs with third part Inktec ink. Only when a cartridge is replaced sometimes I need to perform an extra cleaning cycle, because the magenta or the yellow bands in the nozzle tests are partially contaminated with cyan ink.
 

The Ninth

Getting Fingers Dirty
Joined
Jun 4, 2022
Messages
31
Reaction score
20
Points
28
Location
Vienna
Printer Model
Canon PRO-1000
This printer is starting to get up my nose, its doing things that no normal printer has done on me before..
What printer model are we talking about here?
 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
What printer model are we talking about here?
Thread header "Maxify is the Pitts.."
Al the Maxify printer models have the same internal print layout, mine is the Maxify 5155..
 

The Ninth

Getting Fingers Dirty
Joined
Jun 4, 2022
Messages
31
Reaction score
20
Points
28
Location
Vienna
Printer Model
Canon PRO-1000
Thread header "Maxify is the Pitts.."
Al the Maxify printer models have the same internal print layout, mine is the Maxify 5155..
Ah, thanks, learned something again, did not know that "Maxify" is a printer series from Canon. 🙈
 

palombian

Printer Master
Joined
Feb 4, 2014
Messages
1,869
Reaction score
2,244
Points
297
Location
Belgium
Printer Model
PRO10,PRO9500II,MB5150,MG8250
I've got cloggs on some colours too, without an understandable pattern, a strange beast indeed.
I am happy now and print a lot, IMO the machine likes this.
C and Y are from GI-56 bottles, M is still happy with octopus-office.de, and BK is from an expired PFI-701BK cart.
As said, trial and error.
 
Last edited:

Redbrickman

Printer Master
Joined
Dec 27, 2010
Messages
1,102
Reaction score
1,183
Points
293
Location
UK
Printer Model
MB5150
Thread header "Maxify is the Pitts.."
Al the Maxify printer models have the same internal print layout, mine is the Maxify 5155..

Mine will never print the yellow nozzle check strip unless I select high quality. I agree they are a quirky printer range but I think Palombian made a valid point in that they like to be printng regularly.

The most important thing I have found when refilling is to get as much air as possible out at the end as it seems to make a difference as far as any initial leaks goes after putting in the carts.

Mine has just thrown a couple of low ink warnings so it is time for another battle with it :)
 

Artur5

Printer Master
Joined
Jan 24, 2011
Messages
1,294
Reaction score
1,618
Points
278
Location
Kmt. 0.
Printer Model
MB5150,Pro10s,i3Mk3s+,Voron2.4
Maxify and Pixma range of printers apparently are designed and manufactured by different divisions inside Canon. So, what applies for Pixmas it doesn't for the Maxifys and vice-versa.
The ARC on the cyan cart of my MB5150 refused to return to full condition after it was declared empty and reinstalled. It has remained in 'unknown' condition for months, but cyan ink continues to flow normally for the time being. I'm curious to know what will happen when the ink control chamber detects that the cyan ink is exhausted. Some kind of error, I suppose,
 

palombian

Printer Master
Joined
Feb 4, 2014
Messages
1,869
Reaction score
2,244
Points
297
Location
Belgium
Printer Model
PRO10,PRO9500II,MB5150,MG8250
Mine will never print the yellow nozzle check strip unless I select high quality. I agree they are a quirky printer range but I think Palombian made a valid point in that they like to be printng regularly.

The most important thing I have found when refilling is to get as much air as possible out at the end as it seems to make a difference as far as any initial leaks goes after putting in the carts.

Mine has just thrown a couple of low ink warnings so it is time for another battle with it :)
Low ink doesn't cause problems anymore.
When a colour (with ARC) goes empty, I open the front door, remove the cart and refill it in the basement (and seal the ink outlet with a piece of alu tape).
IMO it is less hassle to respect the official procedure instead of refilling all together (as with resettable chips). I don't care about the eventual extra ink flushing, it occurs with fresh OEM carts too and it is a good cleaning.

With 2500 carts I have to do this about every 2 months.
When you are in this routine the ARC's, once synchronized, seem to follow the actual ink levels quite well.
Since it is not mandatory to refill immediately after the red cross appears, with some feeling you can postpone this and adjust the ink level to the chip.
There is a second protection level, although it doesn't always work.
So watch your printer output.
 
Last edited:

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
I'm curious to know what will happen when the ink control chamber detects that the cyan ink is exhausted. Some kind of error, I suppose,
Everybody seems to agree.. the Maxify loves to play truant on you where possible, but overall it’s a hardy old printer.. I must say, I still have a great affection for the Feckin thing, even if it does drive me crazy some days..
 
Top