Search results

Great trick you found out, @Hat, and glad your printer is OK again.

Maybe B504 is not only a protection against missing ink flow, but scares also people doing unconventional things with cartridges. There are some videos about resetting the printer (a manipulation that looks like entering service mode). https://www.inkhub.com.au/ink/b504-error-canon-maxify-printers

Just thinking but no answer... B504 is raised when the printer does not detect ink flow (with the sensor in the printhead). Strange enough this should not have occurred since there was enough ink (or the sensor should have failed or the magenta channel clogged). The error should clear after...

I didn't permit them nagging me when installing the printer.

Maybe mixing margin settings in the printer driver with those in LR/PS causes this. I never change anything in the printer settings and the margins correspond with what is set in LR (PRO-10, PRO-9500II). I print borderless most of the time and until now was able to clean up the mess in the...

I see. But why not have 2 of them ? Every professional photographer has a backup camera body. A printer takes more room of coarse, but I have both my PRO-10 and PRO-9500II one above the other on a recovered TV table.

Sad you abandoned such a good printer despite resetting the counter is perfectly possible. And even if it failed, what could you loose ? But I understand not everyone has the time for it, or can use this time in a more lucrative way. I was thinking the same many times, I don't blame you ;)

It was announced on Wednesday but it was not delivered in the 2 shops I visited. Didn't go back on Saturday. Thanks for informing I didn't miss anything. I still have 4 boxes "Expertiz" from 2 yrs ago, but since I must have hoarded at least 1500 A4 equivalents (from 10x15 to A3+) of different...

Except you, me and maybe 5 others nobody noticed :D

The border is not mandatory on the sides, in fact it is only to insure stable paper transport at the beginning and the end. PS: you can check the correct functioning of the purge system by spraying distilled water on the pads (with a long needle when the printhead is in the middle position)...

It seems you print borderless. I recently had to clean the ink absorbers of the plate (by spraying distilled water and absorbing with paper towels). There is a printer setting to limit the overspray area, set it to the left to limit ink spell.

PRO-10 inks are difficult to clean. IMO isopropanol doesn't dissolve dried ink. I would try detergent for dishwashing (on the sink, not for the machine).

The PRO-10 is not only better on glossy papers (with good CO) but also on matte and fine art the gamut is better and the blacks deeper than with the PRO-9500(II). Only the nasty 30mm border with fine art settings...

Just passing this as info, no connection with seller https://www.marktplaats.nl/v/audio-tv-en-foto/fotografie-professionele-apparatuur/m1932232961-colormunki-photo

I have a Mustek Scanexpress A3, a very basic machine but all others cost 10 times more. The scan wagon blocks regularly. It glides on one side on a round bar as the printhead in a printer, the other side is just a plastic slider. It is also pressed by a spring against the underside of the glass...

Not bad ! Happy Newyear, Hat ;)

No regret, I have more paper than I ever will use (and ink for at least 2 years). After printing my 2023 calendars (8x12 A4) I still have 4 boxes of 50 sheets Expertiz 300g bought 2 years ago. I also make photo books from time to time, but why not try to print them on the double side papers I...

I never could make profiles for other people since I never did the effort to master ArgyllCMS :eek: . But it saves a lot on ink and paper. Bought last week a box full of good papers, all unopened (Hahnemuhle, Ilford, Canon...) for a song. My stock of Aldi glossy is dwindling and I am afraid...

No problem with this old hardware. Here it is connected on the USB2 hub of my EIZO CS2420 monitor. Only warning: Colornavigator 7.1.8 is the last software supporting the Colormunki (this is not really an issue, but keep a copy of the installation software). Best wishes !

I finally upgraded my PC (for one or another reason Windows never took the initiative, although the hardware is compliant) , it was really very easy. The first time I left all peripherals connected, the upgrade failed and returned gently to Windows 10. With only a screen, keyboard and mouse...