Recent content by frogman

I have printed the B. Atkinson image and what I see is better shadow details in the print which is preconditioned. The neutral rendering curve is different in ColorThink as well, but to be honest, what to make of that I am not sure. I think, I see magenta tint in very deep shadows which is not...

I have managed to alter the CAP480.txt file in order to pre-condition it. It worked and I have now new set of .ti1, .ti2 and a .tif file to print and compare the profiles from original CAP480 and the pre-conditioned one. --------------------------

I got it now.:) Thanks @The Hat . I am on the slow side.. I guess. I doubt, The differences between the CM and the Argyll profiles will be visible on the web, considering my old, cheap scanner. Comparing them on the web might lead you to a wrong conclusion. The main difference, obvious one is...

Yes Ian, I am in this mode. Results as a results are not great. I love photography, but it is a hobby for me, which is not bad as I do it for fun. Attending competitions here and there with moderate success, but plenty of room to improve...I hope..:) I am not sure if that is what you wanted to...

You probably red this article: http://www.ludd.ltu.se/~torger/photography/argyll-print.html He put it very simple, but we will see how it goes... I think the best bet is to modify .txt files we already have. I need to gain some experience with this Command line. :)

I printed couple of pictures. One of them is the Bill Atkinson test file. The ArgyllCMS profile is warmer than the Munki one and match the screen better. I thought I will have better shadows, but I was disappointed. Below 10 nothing is visible on both prints - the one printed with Munki profile...

I am creating another profile for Permajet Oyster paper. It has a high OBA and I am curious how it will print. Will comment in a minute. Pete

So....First profile is done: While creating it this warning appeared: Warning: Gamut mapping is non monotonic - may be not very smooth Profile check, after was created: peak error =2.70 avr error = 0.60 RMS = 0.76 -------------------- ColorThink graph: I will print some evaluation images...

Thanks Ian, Can you post a link to this video please? Yes, I am afraid, I will create a profile with too many reading errors, so wanted to stay on the safe side - bigger patches... -------------------- Thanks for the link. :) Thanks in advance Pete

Thanks, I want bigger patches, that is the only reason. I have no proper ruler at the moment to read the printed CAP480 targets. Patches are 9mm, but that is still too small for me. I would like to change the .bat file in order to print these 480 patches onto 2 A4 sheets. Bigger patches is...

Hello Ian, Sorry for the late reply, Yes, I love my Epson 4880. It is easy to find original Epson carts very cheap, so I can not see the point of using a re-fill. I still have couple of full sets.:) I printed the 480 patches .tif on a A4, but I would like to spread them equally on a 2 A4...

Thanks Emulator, I bought Eizo CS230 bundled with i1 Display Pro before couple of months and its Color Navigator with the i1 Display Pro gives average DeltaE < 1. I wanted to send back the i1 Display Pro for a refund, as I thought I will use the CM instead, but when I saw the CM result with...

Thanks Emulator, Yes, I have the driver installed and shows in Device manager: Argyll LibUSB-win32 devices. I even managed to generate and print the 480 patch target via Qimage. I left it for overnight to dry completely. So, I need to make the ruler now and then read the patches. I hope to not...

All sorted now, When I was updating the driver I did it wrong. I will carry on now and hope for the best...fingers crossed..:) Cheers Pete

There was no original driver installation as i already have a driver for CM - the x-rite driver. I needed only to update the driver(manually), following the argyll installation manual, which I did, but can not find the driver in the "usb" folder, in order to update it. Yes, I work within the...