Latest activity
-
Bbuxiaozizai.com replied to the thread Converting Spyderprint 225 patch target to i1Profiler.I speculate that what profcheck actually check the color difference between the Lab value obtained by patch’s RGB value through the...
-
EEpatcola replied to the thread What 3D printing project are you working on today?.I already had this box of springs from Aliexpress. I made the holes they fit in snug so they don't fall out. I had a strange problem...
-
PThe printer displays error code EC31-2F09. I’ve noticed that the print head doesn’t stop over the purge unit. Before the error appears...
-
PHi Everyone, I am currently using Canon ImagePROGRAF PRO-2000, PRO-4000, and PRO-4100. I’m looking for some technical assistance.
-
Nifty reacted to chaos_engineer's post in the thread I CAN have nice things, right?!?! Pulling the trigger on a Bambu Lab H2S with
Like.
You can still do that, you're just going to have little offsets in heat/purge times going between, say, PLA and PTEG (220c and 240c... -
Nifty replied to the thread What 3D printing project are you working on today?.That's fantastic! I've printed a handful of different battery holders and connectors. Some using stripped wire wrapped around a...
-
Nifty reacted to Epatcola's post in the thread What 3D printing project are you working on today? with Like.
Some lithium rechargeable AAA batteries were delivered today. I want them for things that don't work well on the lower voltage of NiMH...
-
chaos_engineer replied to the thread I CAN have nice things, right?!?! Pulling the trigger on a Bambu Lab H2S.You can still do that, you're just going to have little offsets in heat/purge times going between, say, PLA and PTEG (220c and 240c... -
chaos_engineer reacted to Nifty's post in the thread I CAN have nice things, right?!?! Pulling the trigger on a Bambu Lab H2S with Like.
Not bad. Ironically I just watched this great review of it earlier today: Ya, I've wondered about that with the H2D to mix very...
-
Nifty replied to the thread I CAN have nice things, right?!?! Pulling the trigger on a Bambu Lab H2S.Not bad. Ironically I just watched this great review of it earlier today: Ya, I've wondered about that with the H2D to mix very...
-
Nifty reacted to chaos_engineer's post in the thread I CAN have nice things, right?!?! Pulling the trigger on a Bambu Lab H2S with Like.
I'm looking at a multi setup too. I was actually ready to pull the trigger on Flashforge's AD5X, (and the wifey is on board). BUT. I'm...
-
chaos_engineer replied to the thread I CAN have nice things, right?!?! Pulling the trigger on a Bambu Lab H2S.I'm looking at a multi setup too. I was actually ready to pull the trigger on Flashforge's AD5X, (and the wifey is on board). BUT. I'm...
-
chaos_engineer reacted to Nifty's post in the thread I CAN have nice things, right?!?! Pulling the trigger on a Bambu Lab H2S with Like.
Ok friends,I've been around and around and around about this forever! I'm usually (at a fault) frugal <cheap> and have a hard time...
-
Nifty posted the thread I CAN have nice things, right?!?! Pulling the trigger on a Bambu Lab H2S in 3D Printer Models / Reviews / Experiences.Ok friends,I've been around and around and around about this forever! I'm usually (at a fault) frugal <cheap> and have a hard time...
-
EEpatcola replied to the thread What 3D printing project are you working on today?.Some lithium rechargeable AAA batteries were delivered today. I want them for things that don't work well on the lower voltage of NiMH...
-
