New Printer in the Stable

William Seaward

Printer Guru
Joined
May 29, 2016
Messages
208
Reaction score
156
Points
133
Location
Romeoville, IL
Printer Model
Canon Pro 1, 10, 100
If you upload a scan or photo of the EEPROM print out I can translate what I know.

upload_2016-7-16_12-6-1.png
 

PeterBJ

Printer VIP
Platinum Printer Member
Joined
Nov 27, 2010
Messages
5,055
Reaction score
4,896
Points
373
Location
Copenhagen Denmark
Printer Model
Canon MP990
The Pro-1 service manual has no info about deciphering the EEPROM info, but by using info from other service manuals I am able to decipher most of the Pro-1 info.

Starting from the top:

PRO-1 = Printer type. SN=xxxx =Serial Number. USA = Country/Region the printer is intended for. V1.080 = Firmware version. ST = Start Time = Time of installation in format yyyy.mm.dd - hh.mm. LPT = Last Print Time = time for last print without errors. Same time format as LPT.

D=000.0 is ink absorber usage in %. 0 means no ink in the absorber, 100.0 means the absorber capacity is used up. DF is an calculated/estimated number of months to absorber change becoming necessary, based on usage pattern. Ignore this value. W=000.0 = wetting liquid counter. 0 means not used and 100.0 means used up. I think this is also some kind of absorber.

ER (...........) This is a list of the last recorded errors. 10 errors can be recorded, only two are recorded. ER0=1270 means Feed Slot Error. It is a user error when using the manual feed. This is a harmless operator call error. ER1=B200. Normally this is serious. It is a service call error meaning that the print head voltage is abnormal and the print head has failed electronically. But as the printer seems to work normally, I think the error was triggered by some condition during first install and setup of the printer, print head and cartridges. Hopefully it can be ignored.

CHOKE1, CHOKE2, CHOKE3. I don't know what this is, but the printer has a special ink supply system. The value is a time in the same format as LPT. It might be related to the 45 day flush mentioned by The Hat.

TPAGE(TTL=00012) means 12 pages in total were printed.

CH0001 means Count Head =1. This means the print head was installed and never changed or removed from the printer.

CT( LGY=001............) This means Count (ink) Tanks. The value of one for all cartridges means the printer is on its first set of cartridges.

IL( LGY=2.........) IL= Ink Level. This is probably the same as IS= Ink Status for other printers. Ink Status has 4 values. 0=full, 1=middle, 2=low and 3=empty.

P_ON(S=00008) means the printer was turned on 8 times.

A_REG=1, M_REG=0 means the print head was aligned 1 time using automatic alignment and 0 times using the manual alignment.

IF(USB2=1) means the USB2 InterFace is in use.

ASF PAGE(All=00012 PP=00005 Photo1=00002 Photo2=00005 Photo3=00000 Matto=00000 PC=00000 FA=00000) All=12= total number of printed pages. PP=5 means 5 pages printed on Plain Paper. Photo1, Photo2 and Photo3 must be 3 types of photo paper Matto=? PC=Post Card and FA=?

MF PAGE(ALL=00000) means manual feed pages. None were printed. I think All means all formats.

DCDP(All=00000) This is camera direct printed pages. None were printed. I think All means all formats.

EDGE=00002 means 2 borderless prints were made.

SIZE(A3=00000 A4=00012...........) This is a list of the prints made in various formats. Only 12 A4 prints were made.

CDR=00000 No CDs were printed.

CDRP (.........) is CDR Position correction value. CDRS (....) is CDR Sensor correction value. I think these values are factory calibration values.

LF(.....) is a Line Feed correction value. I think this is a factory calibration value.

INK_OFF(LGY=0...........) As all values are 0, this means that Ink level monitoring was never turned off to allow printing with refilled cartridges. If any of the values are 1 this means that that the ink level was turned off. Warranty would then be void.

WD_LAN (MAC........) is the printers WireD Mac address.

LP_WD=00000 means no pages were printed using the LAN connection.

The printer was first installed in February this year. But I wonder when the printer was made, as newer Pro printers seem not to be able to enter service mode by the user. Does the firmware version = V1.080 tell anything?
 
Last edited:

mikem65d

Print Addict
Joined
Oct 2, 2014
Messages
146
Reaction score
176
Points
167
Printer Model
Canon Pro-100, ip6600D, i900D
Peter, that is so cool to see all this info.
 
Top