Keep your powder dry!

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
Nice one, so you don’t have to take all the reels, just to replace an empty, my single shart system is already up and running but I’ll look further in this guys idea, because it has merits..
Thanks @Redbrickman...
 

Nifty

Printer VIP
Administrator
Joined
Nov 3, 2004
Messages
3,046
Reaction score
1,405
Points
337
Location
Bay Area CA
Printer Model
CR-10, i560 ,MFC-7440N
That's a pretty cool design!

I need to figure out what's going on with my dry box since the filament is binding in the bowden tube and results in under extrusion :(
 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
since the filament is binding in the bowden tube and results in under extrusion :(
This just might be what you’re looking for...
I am seriously thinking of remodeling my box...
 

Hector Vilches

Printing Ninja
Joined
Jan 9, 2016
Messages
42
Reaction score
69
Points
80
Location
New Jersey
Printer Model
R2000, 3880, PRO-100, PRO-10
I need to figure out what's going on with my dry box since the filament is binding in the bowden tube and results in under extrusion :(

Could also be the PTFE tube getting old/dirty/deformed?
 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
I need to figure out what's going on with my dry box :(
Dry Box.png
 

PeterBJ

Printer VIP
Platinum Printer Member
Joined
Nov 27, 2010
Messages
5,055
Reaction score
4,896
Points
373
Location
Copenhagen Denmark
Printer Model
Canon MP990
I think that if the filament bends where it enters the Bowden tube this will cause friction. I think a tangential arrangement like this would be better:

Box 2.jpg
 

Nifty

Printer VIP
Administrator
Joined
Nov 3, 2004
Messages
3,046
Reaction score
1,405
Points
337
Location
Bay Area CA
Printer Model
CR-10, i560 ,MFC-7440N
I'm still troubleshooting. Not sure if it's the PTFE tube, the kink in the filament, the orientation of the spool and/or the dry box, the length of PTFE, etc. etc. etc.

I will say that Peter's drawing is closer to what I found works. My first attempt was with the line more in the middle, like The Hat's drawing, and that resulted in the filament buckling, especially with a full roll.
 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
I will say that Peter's drawing is closer to what I found works.
@PeterBJ drawing does work ok for a while but when the reel gets half way thought then the problems can start, (Direction change) that’s why I suggest using a longer piece of tube that will bend in the direction of the oncoming filament..
 

The Hat

Printer VIP
Platinum Printer Member
Joined
Jan 18, 2010
Messages
15,618
Reaction score
8,691
Points
453
Location
Residing in Wicklow Ireland
Printer Model
Canon/3D, CR-10, CR-10S, KP-3
I’ve been looking further into the problem of drag on the filament as it feeds into the extruder, I noticed that I’m getting a different laydown filament pattern when the extruder has to pull the filament a little bit harder sometimes.
Untitled-1.jpg Click to enlarge..
Instead of using a centre shaft to hold the filament in the dry box I’ve decide to go for the idea that @Redbrickman posted in an earlier thread, I will also be using bigger outlet holes in the side wall to prevent filament drag from occurring as already discussed.
Capture 2.png

I tend not to babysit my 3D printer but when I do I get all sorts of new ideas to help make it run smoother, some of the stuff I use doesn’t always improve my work flow but that doesn’t stop me trying other ideas, My filament has about 1 metre to run after it leaves the reel to get to the extruder.
 

Latest posts

Top